mirror of
https://github.com/esp-rs/esp-hal.git
synced 2025-10-01 14:20:44 +00:00
be184a552d
* CS impl * use CS Mutex in C3 examples * use CS Mutex in S2 examples * Update esp32 example * run fmt * Update S3 examples * Remove uses of unsafe where no longer required * use esp_backtrace in examples * fix import & fmt once more * Bump MSRV to 1.60.0 Co-authored-by: Jesse Braham <jesse@beta7.io>
76 lines
2.0 KiB
Rust
76 lines
2.0 KiB
Rust
//! This shows how to configure UART
|
|
//! You can short the TX and RX pin and see it reads what was written.
|
|
//! Additionally you can connect a logic analzyer to TX and see how the changes
|
|
//! of the configuration change the output signal.
|
|
|
|
#![no_std]
|
|
#![no_main]
|
|
|
|
use esp32c3_hal::{
|
|
clock::ClockControl,
|
|
pac::Peripherals,
|
|
prelude::*,
|
|
serial::{
|
|
config::{Config, DataBits, Parity, StopBits},
|
|
TxRxPins,
|
|
},
|
|
timer::TimerGroup,
|
|
Rtc,
|
|
Serial,
|
|
IO,
|
|
};
|
|
use esp_backtrace as _;
|
|
use esp_println::println;
|
|
use nb::block;
|
|
use riscv_rt::entry;
|
|
|
|
#[entry]
|
|
fn main() -> ! {
|
|
let peripherals = Peripherals::take().unwrap();
|
|
let system = peripherals.SYSTEM.split();
|
|
let clocks = ClockControl::boot_defaults(system.clock_control).freeze();
|
|
|
|
let mut rtc = Rtc::new(peripherals.RTC_CNTL);
|
|
let timer_group0 = TimerGroup::new(peripherals.TIMG0, &clocks);
|
|
let mut timer0 = timer_group0.timer0;
|
|
let mut wdt0 = timer_group0.wdt;
|
|
let timer_group1 = TimerGroup::new(peripherals.TIMG1, &clocks);
|
|
let mut wdt1 = timer_group1.wdt;
|
|
|
|
// Disable watchdog timers
|
|
rtc.swd.disable();
|
|
rtc.rwdt.disable();
|
|
wdt0.disable();
|
|
wdt1.disable();
|
|
|
|
let config = Config {
|
|
baudrate: 115200,
|
|
data_bits: DataBits::DataBits8,
|
|
parity: Parity::ParityNone,
|
|
stop_bits: StopBits::STOP1,
|
|
};
|
|
|
|
let io = IO::new(peripherals.GPIO, peripherals.IO_MUX);
|
|
let pins = TxRxPins::new_tx_rx(
|
|
io.pins.gpio1.into_push_pull_output(),
|
|
io.pins.gpio2.into_floating_input(),
|
|
);
|
|
|
|
let mut serial1 = Serial::new_with_config(peripherals.UART1, Some(config), Some(pins), &clocks);
|
|
|
|
timer0.start(250u64.millis());
|
|
|
|
println!("Start");
|
|
loop {
|
|
serial1.write(0x42).ok();
|
|
let read = block!(serial1.read());
|
|
|
|
match read {
|
|
Ok(read) => println!("Read {:02x}", read),
|
|
Err(err) => println!("Error {:?}", err),
|
|
}
|
|
|
|
block!(timer0.wait()).unwrap();
|
|
}
|
|
}
|